/* $NetBSD: dm9000reg.h,v 1.11 2023/03/25 21:33:46 andvar Exp $ */ /* * Copyright (c) 2009 Paul Fleischer * All rights reserved. * * 1. Redistributions of source code must retain the above copyright * notice, this list of conditions and the following disclaimer. * 2. Redistributions in binary form must reproduce the above copyright * notice, this list of conditions and the following disclaimer in the * documentation and/or other materials provided with the distribution. * 3. The name of the company nor the name of the author may be used to * endorse or promote products derived from this software without specific * prior written permission. * * THIS SOFTWARE IS PROVIDED BY THE AUTHOR ``AS IS'' AND ANY EXPRESS OR IMPLIED * WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF * MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. * IN NO EVENT SHALL THE AUTHOR OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, * INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) * HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY * OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF * SUCH DAMAGE. */ #ifndef _DEV_IC_DM9000REG_H_ #define _DEV_IC_DM9000REG_H_ /* * Registers accessible on the DM9000, extracted from pp. 11-12 from * the data sheet */ /* * There are two interesting addresses for the DM9000 (at least in * the context of the FriendlyARM MINI2440) The I/O or register select * address, which is the base address. The DATA address, which is * located at offset 4 from the base address. * * Chances are that this will not work generally, as it really depends * on how the address lines are mapped from the CPU to the DM9000. * But for now it is a good starting point. */ #define DM9000_IOSIZE 4 #define DM9000_NCR 0x00 /* "network" control */ #define DM9000_NCR_RST (1<<0) /* reset chip, self clear */ #define DM9000_NCR_LBK_MASK (0x06) /* loopback test selection */ #define DM9000_NCR_LBK_SHIFT (1) #define DM9000_NCR_LBK_NORMAL (0<<1) /* normal operation */ #define DM9000_NCR_LBK_MAC_INTERNAL (1<<1) /* MAC loopback */ #define DM9000_NCR_LBK_INT_PHY (2<<1) /* PHY loopback */ #define DM9000_NCR_FDX (1<<3) /* use full-duplex, RO when int PHY */ #define DM9000_NCR_FCOL (1<<4) /* force coll. mode. test only */ #define DM9000_NCR_WAKEEN (1<<6) /* wakeup event enable */ #define DM9000_NCR_EXY_PHY (1<<7) /* select ext. PHY, immune SW reset */ #define DM9000_NSR 0x01 /* "network" status */ #define DM9000_NSR_RXOV (1<<1) /* receive overflow detected */ #define DM9000_NSR_TX1END (1<<2) /* transmit 1 completed, W1C */ #define DM9000_NSR_TX2END (1<<3) /* transmit 2 completed, W1C */ #define DM9000_NSR_WAKEST (1<<5) /* wakeup event, W1C */ #define DM9000_NSR_LINKST (1<<6) /* link is up */ #define DM9000_NSR_SPEED (1<<7) /* 1: 100Mbps, 0: 10Mbps */ #define DM9000_TCR 0x02 /* Tx control */ #define DM9000_TCR_TXREQ (1<<0) /* request to start Tx, self clear */ #define DM9000_TCR_CRC_DIS1 (1<<1) /* disable PAD op on Tx1 */ #define DM9000_TCR_PAD_DIS1 (1<<2) /* disable CRC append on Tx1 */ #define DM9000_TCR_CRC_DIS2 (1<<3) /* disable PAD op on Tx2 */ #define DM9000_TCR_PAD_DIS2 (1<<4) /* disable CRC append on Tx2 */ #define DM9000_TCR_EXCECM (1<<5) /* allow infinite colli. retries */ #define DM9000_TCR_TJDIS (1<<6) /* disable xmit jabber, otherwise on */ #define DM9000_TSR1 0x03 /* transmit completion status 1 */ #define DM9000_TSR2 0x04 /* transmit completion status 2 */ #define DM9000_TSR_EC (1<<2) /* aborted after 16 collision */ #define DM9000_TSR_COL (1<<3) /* collision detected while xmit */ #define DM9000_TSR_LCOL (1<<4) /* out of window "late" collision */ #define DM9000_TSR_NC (1<<5) /* no carrier signal found */ #define DM9000_TSR_CLOSS (1<<6) /* loss of carrier */ #define DM9000_TSR_TJTO (1<<7) /* Tx jabber time out */ #define DM9000_RCR 0x05 /* Rx control */ #define DM9000_RCR_RXEN (1<<0) /* activate Rx */ #define DM9000_RCR_PRMSC (1<<1) /* enable promisc mode */ #define DM9000_RCR_RUNT (1<<2) /* accept damaged runt frame */ #define DM9000_RCR_ALL (1<<3) /* accept all multicast */ #define DM9000_RCR_DIS_CRC (1<<4) /* drop bad CRC frame */ #define DM9000_RCR_DIS_LONG (1<<5) /* drop too long frame >1522 */ #define DM9000_RCR_WTDIS (1<<6) /* disable >2048 Rx detect timer */ #define DM9000_RSR 0x06 /* Rx status */ #define DM9000_RSR_FOE (1<<0) /* Rx FIFO overflow detected */ #define DM9000_RSR_CE (1<<1) /* CRC error found */ #define DM9000_RSR_AE (1<<2) /* tail not ended in byte boundary */ #define DM9000_RSR_PLE (1<<3) /* physical layer error */ #define DM9000_RSR_RWTO (1<<4) /* >2048 condition detected */ #define DM9000_RSR_LCS (1<<5) /* late colli. detected */ #define DM9000_RSR_MF (1<<6) /* mcast/bcast frame received */ #define DM9000_RSR_RF (1<<7) /* damaged runt frame received <64 */ #define DM9000_ROCR 0x07 /* receive overflow counter */ /* 7: OVF detected, 6:0 statistic counter */ #define DM9000_BPTR 0x08 /* back pressure threshold */ /* 7:4 back pressure high watermark (3 def), 3:0 jam pattern time (7 def) */ #define DM9000_FCTR 0x09 /* flow control threshold */ /* 7:4 Rx FIFO high w.m. (3 def), low w.m. (8 def) */ #define DM9000_FCR 0x0A /* Rx flow control */ #define DM9000_FCR_FLCE (1<<0) /* flow control enable */ #define DM9000_FCR_RXPCS (1<<1) /* Rx PAUSE current status */ #define DM9000_FCR_RXPS (1<<2) /* Rx PAUSE status, latched R2C */ #define DM9000_FCR_BKPM (1<<3) /* HDX back pressure for my frames */ #define DM9000_FCR_BKPA (1<<4) /* HDX back pressure for any frames */ #define DM9000_FCR_TXPEN (1<<5) /* activate auto PAUSE operation */ #define DM9000_FCR_TXPF (1<<6) /* Tx PAUSE packet (when full) */ #define DM9000_FCR_TXP0 (1<<7) /* Tx PAUSE packet (when empty) */ #define DM9000_EPCR 0x0B /* EEPROM / PHY control */ #define DM9000_EPCR_ERRE (1<<0) /* operation in progress, busy bit */ #define DM9000_EPCR_ERPRW (1<<1) /* instruct to write, not SC */ #define DM9000_EPCR_ERPRR (1<<2) /* instruct to read, not SC */ #define DM9000_EPCR_EPOS_EEPROM (0<<3) /* EEPROM operation */ #define DM9000_EPCR_EPOS_PHY (1<<3) /* PHY operation */ #define DM9000_EPCR_WEP (1<<4) /* EEPROM write enable */ #define DM9000_EPCR_REEP (1<<5) /* reload EEPROM contents, not SC */ #define DM9000_EPAR 0x0C /* EEPROM / PHY address */ #define DM9000_EPAR_EROA_MASK 0x3F /* 7:6 (!!) PHY id, 5:0 addr/reg */ #define DM9000_EPAR_INT_PHY 0x40 /* EPAR[7:6] = 01 for internal PHY */ #define DM9000_EPDRL 0x0D /* EEPROM / PHY data 7:0 */ #define DM9000_EPDRH 0x0E /* EEPROM / PHY data 15:8 */ #define DM9000_WCR 0x0F /* wakeup control and status */ #define DM9000_MAGIC (1<<0) /* magic frame arrived */ #define DM9000_SAMPLE (1<<1) /* sample frame arrived */ #define DM9000_LINK (1<<2) /* link change / status change found */ #define DM9000_MAGICEN (1<<3) /* enable magic frame event detect */ #define DM9000_SMAPLEEN (1<<4) /* enable sample frame event detect */ #define DM9000_LINKEN (1<<5) /* enable link change event detect */ #define DM9000_PAB0 0x10 /* my station address 7:0 */ #define DM9000_PAB1 0x11 #define DM9000_PAB2 0x12 #define DM9000_PAB3 0x13 #define DM9000_PAB4 0x14 #define DM9000_PAB5 0x15 /* my station address 47:40 */ #define DM9000_MAB0 0x16 /* 64bit mcast hash filter 7:0 */ #define DM9000_MAB1 0x17 #define DM9000_MAB2 0x18 #define DM9000_MAB3 0x19 #define DM9000_MAB4 0x1A #define DM9000_MAB5 0x1B #define DM9000_MAB6 0x1C #define DM9000_MAB7 0x1D /* 63:56, needs 0x80 to catch bcast */ #define DM9000_GPCR 0x1E /* GPIO control */ #define DM9000_GPCR_GPIO0_OUT (1<<0) /* bit-0 to control PHY */ /* 3:0 select pin I/O direction (0001 def) */ #define DM9000_GPR 0x1F /* GPIO value to read / write */ #define DM9000_GPR_PHY_PWROFF (1<<0) /* power down internal PHY */ #define DM9000_TRPAL 0x22 /* Tx SRAM read pointer 7:0 */ #define DM9000_TRPAH 0x23 /* Tx SRAM read pointer 15:8 */ #define DM9000_RWPAL 0x24 /* Rx SRAM read pointer 7:0 */ #define DM9000_RWPAH 0x25 /* Rx SRAM read pointer 15:8 */ /* VID 0x0a46, PID 0x9000 */ #define DM9000_VID0 0x28 /* vender ID 7:0 */ #define DM9000_VID1 0x29 /* vender ID 15:8 */ #define DM9000_PID0 0x2A /* product ID 7:0 */ #define DM9000_PID1 0x2B /* product ID 15:8 */ #define DM9000_CHIPR 0x2C /* chip revision */ #define DM9000_TCR2 0x2D /* Tx control 2 */ #define DM9000_OTCR 0x2E /* operation test control */ #define DM9000_SMCR 0x2F /* special mode control */ #define DM9000_FB0 (1<<0) /* force shortest back-off time */ #define DM9000_FB1 (1<<1) /* force longest back-off time */ #define DM9000_FLC (1<<2) /* force late collision */ #define DM9000_SM_EN (1<<7) /* serial mode enable */ #define DM9000_ETXCSR 0x30 /* early xmit control and status */ #define DM9000_TCSCR 0x31 /* xmit checksum control */ #define DM9000_RCSCSR 0x32 /* recv checksum control and status */ #define DM9000_MPAR 0x33 /* MII PHY address */ #define DM9000_LEDCR 0x34 /* LED pin control */ #define DM9000_BUSCR 0x38 /* processor bus control */ #define DM9000_INTCR 0x39 /* INT pin control */ #define DM9000_SCCR 0x50 /* system clock turn on control */ #define DM9000_RSCCR 0x51 /* resume system clock control */ #define DM9000_MRCMDX 0xF0 /* "no increment" pre-fetch read */ #define DM9000_MRCMDX1 0xF1 /* "no increment" read */ #define DM9000_MRCMD 0xF2 /* "auto increment" read */ #define DM9000_MRRL 0xF4 /* memory read address 7:0 */ #define DM9000_MRRH 0xF5 /* memory read address 15:8 */ #define DM9000_MWCMDX 0xF6 /* "no increment" write */ #define DM9000_MWCMD 0xF8 /* "auto increment" write */ #define DM9000_MWRL 0xFA /* memory write address 7:0 */ #define DM9000_MWRH 0xFB /* memory write address 15:8 */ #define DM9000_TXPLL 0xFC /* frame len 7:0 to transmit */ #define DM9000_TXPLH 0xFD /* frame len 15:8 to transmit */ #define DM9000_ISR 0xFE /* interrupt status report */ #define DM9000_IOMODE_MASK 0xC0 #define DM9000_IOMODE_SHIFT 6 /* 7:6 I/O size (hard wired) 10b: 8-bit, 00b: 16-bit, 01b: 32-bit */ #define DM9000_ISR_PRS (1<<0) /* receive completed, W1C */ #define DM9000_ISR_PTS (1<<1) /* transmit completed, W1C */ #define DM9000_ISR_ROS (1<<2) /* Rx overflow latch, W1C */ #define DM9000_ISR_ROOS (1<<3) /* Rx overflow cntr overflowed, W1C */ #define DM9000_ISR_UNDERRUN (1<<4) /* Tx underrun detected */ #define DM9000_ISR_LNKCHNG (1<<5) /* link status change detected */ #define DM9000_IMR 0xFF /* interrupt mask */ #define DM9000_IMR_PRM (1<<0) /* enable receive event report */ #define DM9000_IMR_PTM (1<<1) /* enable xmit done event report */ #define DM9000_IMR_ROM (1<<2) /* enable Rx overflow event report */ #define DM9000_IMR_ROOM (1<<3) /* enable Rx overflow cntr ov report */ #define DM9000_IMR_PAR (1<<7) /* use 3/13K SRAM w/ auto wrap */ #endif